Perimeter repair
Stretched corners are cut free and patched so the roof can move.
Flat Roofing
Rubber Roof Repair Clark, NJ
A Clark roofer who works on EPDM can fix peeling seams, punctures, blisters and membrane shrinkage at walls and curbs, without the tar patches that damage rubber. One call to (908) 562-6899 reaches a nearby rubber roof repair pro.
Most EPDM leaks come from a short list of problems. Seams lead the list, since older EPDM roofs were often seamed with liquid adhesive that breaks down over time. Next come punctures from foot traffic, branches or dropped tools, and flashing that tears where the membrane meets walls, curbs and pipes.
Shrinkage is a problem specific to rubber roofs. As the sheet contracts, it pulls on the flashing at walls and edges, lifts the membrane off inside corners and can tear the rubber where it bridges between the roof and the wall. The fix is releasing the tension and adding new flashing, not just caulking the gap.
Please do not reach for a can of tar. Petroleum-based patches attack the rubber and have to be scraped off before a real repair. Instead, catch drips inside, stay off the roof when it is wet and note where stains appear.
Many rubber roof repair calls in Clark also turn up a need for rubber roof installation or flat roof repair.
Need rubber roof repair in Clark? Call (908) 562-6899 to reach a nearby roofing contractor.
Call nowThe process
What happens during a rubber roof repair
EPDM repairs depend on surface preparation more than anything else.
Inspect the roof
The inspection traces the leak from the stain back to seams, flashing and penetrations. The roofer also checks whether water has soaked the insulation underneath.
Clean the rubber
Weathered EPDM is scrubbed with a membrane cleaner to remove dirt, chalking and oxidation. Incompatible old patches come off before anything new goes on.
Priming
EPDM primer is scrubbed into the surface and allowed to flash off until it is tacky but not wet. This step is what lets the patch bond chemically to aged rubber.
Apply the patch
The patch is laid over the primed area and rolled so it bonds completely. Odd shapes like pipe bases and inside corners get uncured flashing.
Fix the laps
Open seams are cleaned, primed and covered with seam tape or a cover strip along their full length. Edges of every patch and seam get a bead of lap sealant.
Fix shrinkage
Where the rubber has pulled away, the roofer relieves the tension, adds new flashing up the wall and secures it with termination bar. A termination bar holds the new flashing in place.
What is included
Repairs a rubber roofer can handle
Coating
A rubber-compatible coating can follow repairs after proper priming.
Pipe boots
Cracked pipe boots and vent flashing are replaced for a tight seal.
Puncture repair
Damaged rubber is covered with new membrane with rounded corners.
Lap sealing
Failed seams get a new cover strip so they stay closed.
Related service
EPDM Roof Repair Clark, NJ
EPDM roof repair follows a strict sequence: clean, prime, patch, roll and seal. A clean, dry surface, a properly dried primer and a firmly rolled patch are what make an EPDM repair hold. Edges then get lap sealant for extra protection.
Weather matters for EPDM repairs in Clark, since primers and adhesives need dry conditions and mild temperatures to bond. Short-term fixes can protect the house until the weather cooperates. A proper patch should follow as soon as possible.
Related service
Rubber Roof Replacement Clark, NJ
Rubber roof replacement makes sense when repairs are no longer keeping up. If the roof has many patches and still leaks, or the insulation is wet in many places, replacement is the better choice. A moisture scan shows how much is still dry.
A new rubber roof can go back on as EPDM, or the roof can switch to TPO or PVC. A tear-off is needed if the insulation is wet or there are already two layers. For a Clark home, an honest assessment saves money in the long run.
Local help
Rubber Roof Repair Near Me
In Clark, EPDM is one of the most common membranes on low slope sections of homes. Homes in Clark and nearby places including Rahway, Colonia, Garwood and Cranford get the most from an EPDM roof when seams and flashing are checked every year or two, which keeps small leaks from becoming big ones.
For rubber roof repair in Clark, NJ or nearby towns like Rahway, Colonia, Garwood and Cranford, call (908) 562-6899 to reach a roofer who covers your street.
Roofs in this climate
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in Clark is busiest after a hard winter and before the next one.
Why call
Why not wait
Less damage
Small roof problems caught early usually stay small repairs.
Local knowledge
Local roofers see the same roofs and storm damage across Clark and nearby towns.
Straight answers
Ask the roofer about the cause, the options and the estimate before work starts.
Rubber Roof Repair FAQ
Why is my rubber roof pulling away from the wall?
Shrinkage is the usual cause. As it shrinks, it pulls on the flashing, stretches across inside corners and can tear at the wall. New flashing and termination bar fix it.
What is the lifespan of an EPDM roof?
EPDM can last 20 years or more, sometimes much longer. Thickness, installation and maintenance all affect its life. Timely repairs to seams and flashing help it get there.
Can I use roofing tar on a rubber roof?
Tar and asphalt roof cement should never go on EPDM. They attack the membrane and make future repairs much harder. Use primer, EPDM cover tape and lap sealant instead.
How is a rubber roof patched?
The process is clean, prime, patch and roll. The roofer scrubs the area with membrane cleaner, applies primer, lets it flash off, then presses down a patch with rounded corners and rolls it firmly. The edges get lap sealant.
Should I coat my EPDM roof?
A coating can extend the life of aging EPDM. Repairs and a compatible primer come first, then the coating. Coatings do not fix wet insulation.
More questions? Call (908) 562-6899
Related services
Rubber Roof Installation
New EPDM rubber roofs laid in wide sheets over insulation and a cover board, with primed and taped seams, planned around the slope and the building.
Learn moreFlat Roof Repair
Fixing open seams, blisters, splits, ponding and failed flashing on flat and low slope roofs, so the roof sheds water again without a full replacement.
Learn moreRoof Coating
Silicone, acrylic and other liquid coatings that renew aging flat, low-slope and metal roofs, when the roof underneath is still dry and solid.
Learn moreRoof Leak Repair
Finding where water gets through the roof and sealing it at the source, before wet decking and insulation turn into rot.
Learn more
Looking for something else?
See all roofing servicesGet rubber roof repair help in Clark
Call now for Clark rubber roof repair and help in the towns around it.